Hi-Temp Wax Pro

Description

Hi-Temp Wax Pro is a very durable underbody & cavity coating based on saponified fatty acids that provides excellent rust protection for sheet metal parts and cavities in OEM quality. It has an excellent penetration and water-repellent power which enables it to soak into the smallest gaps and thus reliably protect the surface for a long time.

Due to its special chemical composition Hi-Temp Wax Pro has an extremely high temperature resistance. The product remains absolutely stable up to a temperature of 170°C. Due to its very high temperature resistance Hi-Temp Wax Pro is extremely well suited for use in the engine compartment of the vehicle and in engine rooms - the product will not run off.
Hi-Temp Wax Pro can be used to protect metal and sheet metal against corrosion during construction or repairs. The product is mostly applied to the inside of doors, chassis parts, beams, etc.

Hi-Temp Wax Pro can also be applied with effect to protect power points, battery poles and other electrical components subject to the effects of weather, dampness, dirt and salt. Hi-Temp Wax Pro ensures that these parts are highly water-repellent, as a result of which faults due to permeating dampness or corrosion can be kept to a minimum.

Hi-Temp Wax Pro is available in different types of packaging: besides the 1 litre can, the product is also deliverable as a 60 litre and 200 litre barrel.

The 1 litre screw-top can be used with a traditional adjustable gun (4-6 bar), with the InnoQuip Multi Sprayer 1,3 l or Multi Sprayer 10 l or with the specially designed InnoQuip Pressure Pot Gun (2-4 bar). The wide range of settings available on this gun allows you to spray layers of any thickness. For optimal treatment of cavities use the Cavity Tube Set. 

Properties

• Good flow qualities during application.
• No long-term dripping after application.
• Perfect protection against rust.
• High temperature resistance (up to +170°C). The product does not return to liquid state even in extremely hot conditions.
• Not sensitive to many chemicals such as brake oil, salt, etc.
• OEM approved.
• Perfectly sprayable with a low pressure sprayer, e.g. the InnoQuip Multi Sprayer 1,3 l or Multi Sprayer 10 l.
• Contains 0,1% UV Indicator which makes it easy to check during and after application which parts have been treated or not. Use a suitable UV lamp or blacklight to check this.

Instructions for use

• Surface preparation: The surface must be clean, dry and free of grease. Clean surfaces with Innotec Multisol or Innotec Seal and Bond Remover.
• Application method: Shake or stir well before use. Spray with a traditional adjustable gun (4-6 bar), with the InnoQuip Multi Sprayer 1,3 l or Multi Sprayer 10 l or with the specially designed Pressure Pot Gun (2-4 bar, art.no. 90.0946). See directions for use of the Pressure Pot Gun. Spraying distance 25-30 cm. Apply a dense and evenly sprayed layer. When applying to cavities, use the special extension set (Cavity Tube Set, art.no. 90.1001).

Technical information

• Base: Soaped grease acids
• Density: 870 kg/m³
• Consistency: Liquid
• Solvents: Mixture of aromatic-free solvents and additives
• Flash point: 62°C (according to DIN 53213)
• Temperature resistance: -40°C to +170°C (melting point 170°C)
• Water resistance: Excellent
• Tests: Salt spray test (according to DIN 50021): excellent after 3850 hours, Ri 0 at 100µ dry layer
• Application conditions: +15°C to +35°C
• Type of surface: Ferrous and non-ferrous metals
• Surface preparation: The surface must be clean, dry and free of grease. Clean surfaces with Innotec Multisol or Innotec Seal and Bond Remover.
• Application method: Shake or stir well before use. Spray with a traditional adjustable gun (4-6 bar), with the InnoQuip Multi Sprayer 1,3 l or Multi Sprayer 10 l or with the specially designed Pressure Pot Gun (2-4 bar, art.no. 90.0946). See directions for use of the Pressure Pot Gun. Spraying distance 25-30 cm. Apply a dense and evenly sprayed layer. When applying to cavities, use the special extension set (Cavity Tube Set, art.no. 90.1001).
• Dust dry: Remains somewhat sticky.
• Curing time: (± 100µ) 4-6 hours at 20°C / 65% relative humidity
  Note: The drying process can be strongly influenced by exposing the applied material to a gooed ventilation and/or air flow.
• Recommended layer thickness: 200µ to 250µ wet (dense layer)
• Cleaning of materials used: With Innotec Multisol
• Cleaning of hands: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water
• Shelf life: 2 years in original, unopened packaging
• Storage conditions: Store cool and dry
• Type of batchcode: F
• Other details: 0,1% UV Indicator
  OEM approved
• EAN Code: 5400563009604