Quick Bond

Description

Quick Bond and Quick Bond Activator are unique products especially designed for the quick repair and gluing of metals and almost every type of modern synthetic.
Quick Bond is a special gel which stays in place because it does not run. This means no drips to damage underlying parts and no more gluing of fingers.

The extremely long open time ensures that parts can be perfectly lined up when gluing. When the time comes to form a bond, Quick Bond Activator is applied to start an immediate reaction.

Quick Bond adheres perfectly to plastics and lacquered or bare metal parts. The product cures in seconds once the Activator is sprayed on, and can be manipulated or stressed immediately.

In the Automotive and Industry sectors, plastic supports, hooks, clips, bolts, and so on break off on a regular basis. Use Quick Bond to make a perfect repair. If the bond is to be placed under heavy load it can be reinforced using Repaplast Repair Grey or Repaplast Repair Black, and the Quick Bond used as a fixer.

Quick Bond's transparency means that no fracture line can be seen, and the product is ideal for gluing plastic rear lights, indicators, flashing lights, PMMA panels, displays, etc. It can also be used to fill holes in headlamp glass.
In jobs involving electronics Quick Bond can be used to fix wires in a simple but effective manner.
As part of the Repaplast Scratch Repair System this product can be used to fill scratches in textured plastic, before finishing with Repaplast Structure Coat and Repaplast Colour Finish Better Care.

Packaged in a handy 10 g tube with cannula, Quick Bond is easy to use and administer. Thanks to the unique easy-close cap (Quick Bond Nozzle) the tube can be opened time and again without a problem, and has a longer storage life.

See also: Repaplast Scratch Repair System

Properties

• Quick drying.
• Colourless.
• Excellent adhesion.
• Easy to use, no mixing needed.
• Thixotropic.
• Cures at room temperature.

Instructions for use

• Surface preparation: The surface must be clean, dry and free of grease. Roughen up or sand the surface. Clean metal surfaces with Innotec Multisol or Innotec Seal and Bond Remover. Clean plastic surfaces with Innotec Repaplast Cleaner Antistatic and pre-treat them with Innotec Repaplast Primer.
• Application method: When gluing: Give one part a thin layer of Quick Bond, spray the other part with a thin layer of Quick Bond Activator, and join the parts together. Allow a few minutes for Quick Bond to dry.
  When repairing: Apply Quick Bond straight from the tube to the repair area. Smooth with a filling knife or spatula. Wait 30 seconds and apply a thin layer of Quick Bond Activator over the element repaired with Quick Bond. It will take only a few seconds to harden.

Technical information

• Base: Ethyl cyano acrylate
• Density: ± 1000 kg/m³
• Consistency: Thixotropic gel
• Solvents: Mixture of aliphatic solvents
• Temperature resistance: -60°C to +80°C
• Moisture resistance: Moderate. Not suited to prolonged immersion in water.
• Solvent resistance: Moderate
• Application conditions: +5°C to +35°C
• Type of surface: Just about all modern plastics and metals
• Surface preparation: The surface must be clean, dry and free of grease. Roughen up or sand the surface. Clean metal surfaces with Innotec Multisol or Innotec Seal and Bond Remover. Clean plastic surfaces with Innotec Repaplast Cleaner Antistatic and pre-treat them with Innotec Repaplast Primer.
• Application method: When gluing: Give one part a thin layer of Quick Bond, spray the other part with a thin layer of Quick Bond Activator, and join the parts together. Allow a few minutes for Quick Bond to dry.
  When repairing: Apply Quick Bond straight from the tube to the repair area. Smooth with a filling knife or spatula. Wait 30 seconds and apply a thin layer of Quick Bond Activator over the element repaired with Quick Bond. It will take only a few seconds to harden.
• Sandability: Good, after a few minutes. If you need to spray over Quick Bond, sand the repair area with P120, P220 and P320 successively.
• Paintability: Good. Clean plastic surfaces with Innotec Repaplast Cleaner Antistatic and pre-treat them with Innotec Repaplast Primer. Spray over with Innotec Repaplast Structure Coat and/or Innotec Repaplast Colour Finish Better Care.
• Cleaning of materials used: With Innotec Multisol
• Cleaning of hands: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water
• Shelf life: 18 months in original, unopened packaging.
  If Quick Bond is stored at a temperature of ± 15°C to 25°C the product has a shelf life of only 6 months!
• Storage conditions: Store cool, dry and dark (5°C to 15°C)
• Type of batchcode: F
• EAN Code: 5400563001349