Spray-Seal HS-m 290 ml Black

Art.: 01.3469.0000 Black
Cartridge 290 ml

Spray-Seal is an aromatic-free, sprayable bodywork sealant, which, thanks to its unique composition and application options, makes it easy to perfectly imitate the factory original seams and structures on sheet metal parts for many makes of cars.

More info
This product is currently not available for order.
Please contact your local distributor.

Safety data sheet

To order, please contact your distributor

Description

Spray-Seal is an aromatic-free, sprayable bodywork sealant, which, thanks to its unique composition and application options, makes it easy to perfectly imitate the factory original seams and structures on sheet metal parts for many makes of cars.

Thanks to its unique MS polymer composition Spray-Seal can be worked extremely finely without overspray or 'spider-webbing'. As a result, Spray-Seal can be sprayed over wet-on-wet after 30 minutes.

Spray-Seal is isocyanate-free and retains its elasticity at all times. Due to its excellent adhesion, it also provides good protection to the treated surface.

Spray-Seal comes in two variants: Spray-Seal HS-m and Spray-Seal LS-m.

Due to its high constancy Spray-Seal HS-m is ideal for very coarsely sprayed structures requiring a very thick layer of product. The product can also be used with a sealant spray, so that precision seams such as door seams can be applied perfectly, and the product can also be applied with a nylon brush.

Since it is easy to spray and set for different structures, Spray-Seal LS-m is ideal for large surfaces. Thanks in part to its sound insulating properties Spray-Seal LS-m is ideal for floor panels, wheel arches and sills.

The handy 290 ml cartridges make Spray-Seal very economical and easy to use. The wide range of settings available with the special Sealer Applicator makes it possible to imitate just about any structure. The Sealer Applicator is made in such a way that an open sealant cartridge will keep in the pistol for a very long time. This also keeps cleaning to a minimum.
When brushing the sealant it is recommended to use the InnoQuip Brush for best results.

Spray-Seal is also available in plastic and metal 20 kg barrels (only on demand).

Properties

  • Contains no isocyanates or aromatic hydrocarbons.
  • Very fast skinning and curing.
  • Can be sprayed/painted over wet-on-wet (after 30 minutes).
  • Can be worked finely and is simple to apply.
  • Excellent rust prevention under sealed coating.
  • Permanently elastic.
  • Impact and chip resistant.
  • Available in various factory original colours.
  • Spray-Seal has an extremely long storage life in the Sealer Applicator.
  • OEM approved.

Instructions for use

  • Surface preparation: The surface must be clean, dry and free of grease. Clean surfaces with Innotec Multisol.
  • Application method: Spray at 4 to 5 bar using the specially designed Sealer Applicator. See also the directions for use of the Sealer Applicator.

Technical information

  • Base: MS polymers
  • Density: ± 1520 kg/m³
  • Consistency: Thixotrope
  • Solvents: Isoparaffin mixture
  • Flash point: > 63°C
  • Hardness: 65 (Shore A)
  • Tensile strength: 1,20 N/mm² (according to DIN 53504)
  • Elongation at break (%): 240% (according to DIN 53504)
  • Modulus: ± 1,20 N/mm² (100% elongation) (according to DIN 53504)
  • Temperature resistance: -40°C to +90°C (short-time limit +130°C after full curing)
  • UV resistance: Good, in case of sufficient layer thickness (min 3 mm)
  • Water resistance: Good
  • Solvent resistance: Reasonable
  • Acid resistance: Good, to weak acids
  • Slump resistance (stability): Good
  • Percentage of solids: ± 90%
  • Shrinkage: ± 12%
  • Application conditions: +5°C to +40°C
  • Type of surface: Preferable: primered metal
  • Surface preparation: The surface must be clean, dry and free of grease. Clean surfaces with Innotec Multisol.
  • Application method: Spray at 4 to 5 bar using the specially designed Sealer Applicator. See also the directions for use of the Sealer Applicator.
  • Skin formation: ± 10 minutes (at 23°C / 50% relative humidity)
  • Tack free: ± 30 minutes (at 23°C / 50% relative humidity)
  • Curing time: ± 3 mm / 24 hours (at 23°C / 50% relative humidity)
  • Paintability: Can be sprayed over after ± 30 minutes using just about any type of modern (priming) paint system. After 4 hours Spray-Seal HS-m must be pre-treated with Innotec Repaplast Primer before painting with water based paint systems. This will ensure a quicker and better adhesion. Due to the huge variety of paint types on the market, it is best to test the paint beforehand.
  • Cleaning of materials used: With Innotec Multisol
  • Cleaning of hands: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water
  • Shelf life: 1 year in original, unopened packaging
  • Storage conditions: Store cool and dry
  • Type of batchcode: F
  • Other details: OEM approved
  • EAN Code: 5400563006047

Only quality has a future